[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Thecus N1200

OpenBSDで動くのならば、というわけでやってみました。
まだ完全じゃありませんが、ちと飽きてきたので。:-)
ソースコードはそのうちいつものところにおいておきます。
(まだとても他人に見せられない:-)


U-Boot 1.1.3 (FSL Development) (Jan 31 2007 - 17:57:16) MPC83XX

Clock configuration:
  Coherent System Bus:  266 MHz
  Core:                 266 MHz
  Local Bus Controller: 266 MHz
  Local Bus:             33 MHz
  DDR:                  266 MHz
  I2C:                  266 MHz
  TSEC1:                266 MHz
  TSEC2:                266 MHz
  USB MPH:               88 MHz
  USB DR:                88 MHz
CPU: MPC83xx, Rev: 11 at 266.666 MHz
Board: Thecus N1200
I2C:   ready
DRAM:  SDRAM on Local Bus is NOT available!
   DDR RAM: 128 MB
FLASH:  8 MB
PCI1 32bit on PMC1 & PMC2 & PMC3
In:    serial
Out:   serial
Err:   serial
Net:   Freescale TSEC0: PHY is Realtek RTL8211B (1cc912)
Freescale TSEC1: PHY id 1410c87 is not supported!
Freescale TSEC1: No PHY found
Freescale TSEC0, Freescale TSEC1
Thecus Version: 3, PIC version: 4
Hit any key to stop autoboot:  0 
=> boot
Speed: 100, full duplex
BOOTP broadcast 1
Using Freescale TSEC0 device
TFTP from server 10.1.1.1; our IP address is 10.1.1.12
Filename 'netbsd.ub'.
Load address: 0x100000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ################################################################
done
Bytes transferred = 1987864 (1e5518 hex)
## Starting application at 0x00100000 ...
[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.63 (N1200) #99: Sun May 25 22:42:14 JST 2008
	tsubai@sakura:/a/0519/src/sys/arch/n1200/compile/N1200
total memory = 128 MB
avail memory = 122 MB
mainbus0 (root)
cpu0 at mainbus0: 8347 (Revision 11), ID 0 (primary)
cpu0: HID0 90c000<DOZE,DPM,ICE,DCE>
cpu0: HID1 44000000<PC1,PC5>
cpu0: HID2 0
lb0 at mainbus0
com0 at lb0 addr 0x4500 irq 9: ns16550a, working fifo
com0: console
com1 at lb0 addr 0x4600 irq 10: ns16550a, working fifo
tsec0 at lb0 addr 0x24000 irq 32,33: address 00:14:fd:10:93:d2
rgephy0 at tsec0 phy 17: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
tsec1 at lb0 addr 0x25000 irq 35,36: address 00:14:fd:10:93:d3
mvphy0 at tsec1 phy 1: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvphy1 at tsec1 phy 2: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvphy2 at tsec1 phy 3: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvphy3 at tsec1 phy 4: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ehci0 at lb0: addr 0x22100 irq 39
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
pbi0 at lb0: addr 0x8300
pci0 at pbi0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: unknown vendor 0x1957 product 0x0085 (rev. 0x11)
satalink0 at pci0 dev 16 function 0: Silicon Image SATALink 3512 (rev. 0x01)
satalink0: SATALink BA5 register space disabled
satalink0: bus-master DMA support present
satalink0: using irq 20 for native-PCI interrupt
atabus0 at satalink0 channel 0
atabus1 at satalink0 channel 1
pbi1 at lb0: addr 0x8380
pci1 at pbi1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 0 function 0
pchb1: unknown vendor 0x1957 product 0x0085 (rev. 0x11)
uhub0 at usb0: MPC8347 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
boot device: <unknown>
root on tsec0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 10.1.1.1
nfs_boot: my_addr=10.1.1.12
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=10.1.1.1
root on sakura:/e/ppc32
WARNING: no TOD clock present
Enter pathname of shell or RETURN for /bin/sh: 
We recommend creating a non-root account and using su(1) for root access.
# 


http://nandra.segv.jp/NetBSD/n1200.html
にも同じものがあります。時々更新しています。

余談ですが、本来の使い方をやってみようとしたら、私には
セットアップすらできませんでした。http でできないとは
思わなかった…。